Contact Us Live Chat or 1-888-505-1906
My Garage
Cart
Make sure this part fits

Acura 50800-SD4-013 Mounting Assembly, Front Engine

1986 Acura Legend 50800SD4013

Customer Questions & Expert Answers (2)
Acura 50800-SD4-013 Mounting Assembly, Front Engine
  • Part Description
    Crossmember Insulator
  • Position
    Front
  • Manufacturer
    Acura
Make sure this part fits
$94.42 MSRP: $132.47
You Save: $38.05 (29%)
Ships in 1-2 Business Days
1
ADD TO CART
  • Related Parts
  • Product Specifications
  • Vehicle Fitment
  • Customer Questions & Expert Answers
  • Product Specifications

    BrandGenuine Acura
    Manufacturer Part Number50800-SD4-013
    Part DescriptionCrossmember Insulator
    Other NamesFront Mount
    Item Dimensions8.0 x 7.2 x 6.6 inches
    Item Weight3.90 Pounds
    PositionFront
    ConditionNew
    Fitment TypeDirect Replacement
    ManufacturerAcura
    SKU50800-SD4-013
    WarrantyThis genuine Acura part is guaranteed by Acura's factory warranty.
    Shipping & ReturnShipping Policy Return Policy
    Warning: California's Proposition 65
  • Vehicle Fitment

    Year Make Model Body & Trim Emission & Transmission
    1986 Acura Legend4 Door LXKA 4AT, KA 5MT, KL 4AT, KL 5MT
  • Customer Questions & Expert Answers

    Q:
    Is this the correct part for my vehicle? Posted by AcuraPartsWarehouse Specialist
    A:
    You can Select Your Vehicle to check if 50800-SD4-013 fits your vehicle.
    Posted by AcuraPartsWarehouse Specialist
    Q:
    How to inspect, maintain, and replace engine mounts and torque rods on Acura Legend? Posted by Customer
    A:
    But engine mounts are usually something that doesn't need any attention, unless they are broken or worn, at which point they should be replaced immediately to protect driveline components. To check the mounts, jack the engine slightly and take weight off of the mounts; make sure the vehicle is supported on jackstands with a jack centered under the oil pan and protected with a block of wood if the block will be damaged. Look for cracks in the mounts or in hardened rubber, or separation between the mounts and the engine or frame; if movement exists between the mount plates and engine or frame, this may need to be tightened down with fasteners. Rubber preservative can slow deterioration by applying it. If you're not already already, disconnect the negative battery cable, set the parking brake, block the rear wheels and raise the front of the vehicle securely on jackstands. The weight bearing mounts and the torque rod make up the engine mounting system, with the upper mount fastened near the timing belt, and the lower mount between the crossmember and the engine. Most of the engine weight-supported by the front and rear mounts which are bolted on to the crossmembers and which are positioned relatively low, between the engine and firewall and between the engine and radiator-is bolted to the cross members. The torque rod reduces twisting forces on the mounts and, with automatic transaxle models, an additional upper transaxle mount. During final tightening, it should be level with the engine weight on the mounts, to prevent bushings from twisting or being offset too much for optimal bushing life, and to minimize noise and vibration. If you are replacing mounts, raise the engine up using a floor jack and set a block of wood over the oil pan so you protect it. Remove retaining bolts, and slide out the lower mount, then install new mount, and tighten fasteners securely. Remove the mount to bracket nut, then unbolt the mount from the bracket and lift it out, lift the engine to do so, for the front and rear mounts. Drop the engine on the new mount, tighten the nut and install the new mount on the crossmember. The upper mount carries little weight and almost never fails, however when the engine is removed you should inspect and replace it, much like you would change a car muffler; remove the through bolt and pull the mount from its bracket reinstalling it in reverse order and tighten bolts securely. Unbolt the torque rod from both the engine and frame brackets, lift it out and re-bolt it back into the same order, ensured that all bolts are tight.
    Posted by AcuraPartsWarehouse Specialist
    If you have any questions about this product, please don't hesitate to ask us. We will be happy to help you!

Genuine Acura Part 50800-SD4-013, the Right Choice

To ensure reliability, purchase Acura part # 50800-SD4-013 Mounting Assembly, Front Engine. It is sometimes referred to as Acura Engine Mount. When it comes to quality and durability, OEM parts reign supreme. They are manufactured to meet Acura's exacting factory specifications and undergo rigorous quality control. This part fits 1986 Acura Legend.

AcuraPartsWarehouse.com is a leading supplier of genuine Acura parts and accessories such as Acura 50800SD4013 Mounting Assembly, Front Engine. Welcome to our website where you can procure brand new OEM Acura parts. We boast a wide array of genuine Acura parts at competitive prices. If you're seeking a combination of quality, reliability, durability, and affordability, you've come to the right place. All our parts are backed by a manufacturer's warranty for your peace of mind.

Why choose Acura Parts Warehouse

  • Dedicated Service

    Your complete satisfaction is our #1 goal

  • Lowest Prices

    Best deals on genuine OE parts from dealerships

  • Fast Delivery

    Orders are processed and delivered promptly