Contact Us: Live Chat or 1-888-505-1906
My Garage
My Account
My Cart
Make sure this part fits your vehicle

Acura 51605-ST7-902 Right Front Shock Absorber Unit (Showa)

1994-2001 Acura Integra 51605ST7902

Acura 51605-ST7-902 Right Front Shock Absorber Unit (Showa)
  • Part Description
    Shock Absorber Unit, Right Front (Showa) ; Strut
  • Position
    Front Passenger Side
  • Replaces
    51605-ST7-901
  • Manufacturer
    Acura
  • Manufacturer's Notes
    This part is discontinued.
Customer Questions & Answers
  • Product Specifications

    BrandGenuine Acura
    Manufacturer Part Number51605-ST7-902
    Part DescriptionShock Absorber Unit, Right Front (Showa) ; Strut
    Other NamesStrut
    Item Dimensions26.0 x 8.9 x 7.7 inches
    Item Weight2.30 Pounds
    PositionFront Passenger Side
    ConditionNew
    Fitment TypeDirect Replacement
    Replaces51605-ST7-901
    ManufacturerAcura
    SKU51605-ST7-902
    WarrantyThis genuine Acura part is guaranteed by Acura's factory warranty.
    Shipping & ReturnShipping Policy Return Policy
    Warning: California’s Proposition 65
  • Vehicle Fitment

    Year Make Model Body & Trim Emission & Transmission
    2001 Acura Integra3 Door GS, 3 Door GS-R, 3 Door LSKA 5MT
    2000 Acura Integra3 Door GS, 3 Door GS-R, 3 Door LSKA 5MT
    1999 Acura Integra3 Door GS, 3 Door GS-R, 3 Door LS, 3 Door RSKA 5MT
    1998 Acura Integra3 Door GS, 3 Door GS-R, 3 Door LS, 3 Door RSKA 5MT
    1997 Acura Integra3 Door GS, 3 Door GS-R, 3 Door LS, 3 Door RSKA 5MT
    1996 Acura Integra3 Door GS-R, 3 Door LS, 3 Door RSKA 5MT
    1995 Acura Integra3 Door GS-R, 3 Door LS, 3 Door RSKA 5MT
    1994 Acura Integra3 Door GS-R, 3 Door LS, 3 Door RSKA 5MT

Customer Questions & Answers

Q:
Is this the correct part for my vehicle? Posted by AcuraPartsWarehouse Specialist
A:
You can Select Your Vehicle to check if 51605-ST7-902 fits your vehicle.
Posted by AcuraPartsWarehouse Specialist
Q:
How do you raise the vehicle? Posted by Customer
A:
Use a jack to raise the vehicle and place it securely on jackstands.
Posted by AcuraPartsWarehouse Specialist
See expert answers on similar Shock Absorber
Q:
How do you remove the shock absorber assembly for the 1999 Acura Integra? Posted by Customer
A:
Start by loosening the wheel lug nuts, raising the vehicle, and securing it with jackstands. Remove the wheel. Then, unbolt the brake hose from the shock absorber assembly and disconnect the stabilizer bar from the lower control arm. Position a floor jack beneath the lower control arm to provide support during shock absorber removal. Proceed to remove the damper fork pinch bolt and the damper fork-to-lower control arm bolt, detaching the fork from the shock absorber. Support the shock absorber and coil spring assembly, and take off the two upper mounting nuts, ensuring not to remove the larger center nut. Carefully remove the unit from the fenderwell.
Posted by AcuraPartsWarehouse Specialist
See expert answers on similar Shock Absorber
Q:
What should be done to install the new damper unit for the 2000 Acura Integra? Posted by Customer
A:
Following the tool manufacturer's instructions, install the spring compressor on the spring and compress it sufficiently to relieve all pressure from the damper mounting base. Remove the damper cap, unscrew the self-locking nut while holding the damper shaft with an Allen wrench to prevent it from turning, then carefully lift the compressed spring from the assembly and set it in a safe place. Slide the rest of the parts off of the damper shaft, install the bump stop, bump stop plate (if equipped), dust cover and dust cover plate onto the new damper unit, extend the damper shaft as far as it will go and slide the components down to the damper body, carefully place the coil spring onto the shock absorber body, with the end of the spring resting in the lowest part of the seat, install the spring mounting rubber, lower mounting rubber, damper mounting collar, damper mounting base, seal, upper mounting rubber, damper mounting washer and a new self-locking nut, before tightening the nut, align the previously applied marks on the mounting base and the spring, then tighten the self-locking nut, again using the Allen wrench to prevent the shaft from turning, remove the spring compressor, install the damper cap and install the shock absorber/coil spring assembly.
Posted by AcuraPartsWarehouse Specialist
See expert answers on similar Shock Absorber
If you have any questions about this product, please don't hesitate to ask us. We will be happy to help you!

Genuine Acura Part 51605-ST7-902, the Right Choice

To ensure reliability, purchase Acura part # 51605-ST7-902 Right Front Shock Absorber Unit (Showa). It is sometimes referred to as Acura Shock Absorber. When it comes to quality and durability, OEM parts reign supreme. They are manufactured to meet Acura's exacting factory specifications and undergo rigorous quality control. This part fits 1994-2001 Acura Integra.

AcuraPartsWarehouse.com is a leading supplier of genuine Acura parts and accessories such as Acura 51605ST7902 Right Front Shock Absorber Unit (Showa). Welcome to our website where you can procure brand new OEM Acura parts. We boast a wide array of genuine Acura parts at competitive prices. If you're seeking a combination of quality, reliability, durability, and affordability, you've come to the right place. All our parts are backed by a manufacturer's warranty for your peace of mind.

Why choose Acura Parts Warehouse

  • Dedicated Service

    Your complete satisfaction is our #1 goal

  • Lowest Prices

    Best deals on genuine OE parts from dealerships

  • Fast Delivery

    Orders are processed and delivered promptly